Samsung SDM-090P Manuale Utente

USER’S MANUALDIGITAL MULTIPLEXERSDM-160/SDM-160P/SDM-160M/SDM-160MPSDM-160(gb)00255 6/30/05 11:42 AM Page B-3

Digital Multiplexer 2-1CHAPTER 2. INSTALLATION Preparing for the InstallationThe following information is prepared for safe installation of the unit.T

Precautions when Installing Precautions when Installing• Be sure to turn the unit off before installing.• Avoid shock or vibration since they may caus

Digital Multiplexer 2-3• When replacing built-in fuse, be sure to turn the poweroff, and unplug the unit.• Avoid locating the unit where direct sunlig

UNPACKINGPlace shipping container on a flat surface, cut straps or tape, open top. Then, review the content;the following items should be included:•

Digital Multiplexer 3-1CHAPTER 3. Connecting to Other DevicesThis unit can be connected to other devices such as monitor, camera, VCR, and PC. This ch

3. Connecting to TIME LAPSE VCRWhen connecting the unit to the TIME LAPSE VCR, set “TLV” in “REC TYPE” after selecting “1.RECOUT SET” of SETUP MENU.1.

Digital Multiplexer 3-34. Connecting to ALARM SENSOR1. Connect the ALARM terminal on the Unit’s Rear Panel to the SENSOR CORRESPONDING TOcamera number

5. Remote Control by connecting to PC A. Connecting to RS-232CThe unit can be remote-controlled by connecting to PC in which terminal emulation progra

6. Remote Control using SSC-1000(RS-485)Refer to SSC-1000 manual1. RS-485 Address set-up : Only odd numbers are available.(from 1 to 253)2. Get into C

Digital Multiplexer4-1ENGLISHChapter 4. Basic Method to useInitial operation 1. Turn on power switch.A 4-division screen appears on the monitor if fi

Digital Multiplexer iiIMPORTANT SAFEGUARDS1. Read instructions: All the safety and operating instructions should be read before the appliance is opera

Digital Multiplexer 4-2When desiring to see in the FULL screenThe FULL screen may be seen in the live and tape replay mode, available for 16 channels

Digital Multiplexer4-3ENGLISHWhen desiring to see automatic sequential conversion screen The automatic sequential conversion mode operates in the LIVE

Digital Multiplexer 4-4When desiring to see the stop screenThe monitor screen (full screen and division) may be seen with a temporary stop. A desired

Digital Multiplexer4-5ENGLISHWhen desiring to see in the PIP screenThe PIP (picture in picture) screen may be seen using the “PIP” button on the FULL

Digital Multiplexer 5-1Chapter 5. Setting of Program Menu<MAIN MENU>The following main menu is displayed on the monitor screen if pressing “MENU

Digital Multiplexer5-2ENGLISH- The following screen is displayed if pressing the “ENTER” button with the blinking position placed at the “DUTYSET ….”.

Digital Multiplexer 5-32. Setting of display modeYou can set LIVE/PB display type, PIP size, sequence, and border color, PB IN, etc..The following scr

Digital Multiplexer5-4ENGLISH- The following is displayed if pressing the “ENTER” button with the blinking position placed at the “SPOT OUT...”:• You

Digital Multiplexer 5-5- The following screen is displayed if pressing the “ENTER” button with the blinking position placed at the “LOSSDETECT….”:• Se

Digital Multiplexer5-6ENGLISH• The position of currently input characters is blinking and moves if pressing “ ”, “ ” button.• Select character p

8A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfacesmay cause the appliance and cart com

Digital Multiplexer 5-75. Setting of alarmSet operation when alarm occurs.The following screen is displayed if pressing the “ENTER” button with the bl

Digital Multiplexer5-8ENGLISH- The blinking character moves if pressing “ ”, “ ” button.- The setting value is changed if pressing “ ”, “

Digital Multiplexer 5-97. System setting Set application of password change, buzzer and summer time.The following screen is displayed if pressing the

Digital Multiplexer5-10ENGLISH- The following screen is displayed if pressing the “ENTER” button when the blinking position is at the “PASSWORDCHANGE…

Digital Multiplexer 6-1Chapter 6. Recording1.Normal record modeWhen setting the “REC TYPE” of the setup menu “1.REC OUT SET” to “NOR”.(1) Frame record

Digital Multiplexer6-2ENGLISH3.Weight value (REC DUTY) record- Used to record weight value (record frequency is more than the channel whose duty is lo

Digital Multiplexer 7-1Chapter 7. Occurrence and handling of alarm, loss, motion1.Alarm occurrence conditionsThe following events occur if alarm occur

Digital Multiplexer7-2ENGLISH5.Alarm/Loss list reference If pressing the “LIST” button on the front, alarm, channel loss and motion detection informat

Digital Multiplexer A-1Appendix A Specifications1) Image inputCamera: 16 input (BNC Type, Loop Through)1.0Vp-p, 75 Ω automatic termination, CVBSVCR

Digital MultiplexerA-2ENGLISHOUTSIDE DRAWINGSDM-160(gb)00255 6/30/05 11:42 AM Page A-2

Digital Multiplexer ivCONTENTS CHAPTER 1. INTRODUCTION... 1-1~1-4Introduction...

Digital Multiplexer B-1Appendix B Checking points in troubleThere may be a case not to use system properly since unexpected status occurs while using

Part No.: AB68-00255APrinted in KoreaSDM-160(gb)00255 6/30/05 11:42 AM Page B-2

CHAPTER 5. SETTING OF PROGRAM MENU ... 5-1~ 5-10Record setting of each camera ...

Digital Multiplexer 1-1CHAPTER 1.INTRODUCTIONIntroductionThis unit can combine up to 16 Camera Images onto one VCR, and both frequent recording andseq

Name of parts and FunctionFRONT PANELA. POWER SWITCHPower ON/OFF.B. MULTI SCREEN DISPLAY- MULTI SCREENYou are in the multi-screen mode. Each press of

Digital Multiplexer 1-3E. SETUP/FUNCTION- MENUPressing this Button will make LED lit, and MAIN MENU appears on the screen.- ENTERUsed when switching f

Rear panelA. CAMERA INPUT / LOOP THROUGH OUT - Up to 16 camera signals can be input. When transmitting camera signals to external devices, OUTterminal